Curious about a certain muffler sound and combination? Have a video of yours? Post it here for others to see! Be sure to post what you have for a pipe diameter and muffler setup.

I'll be the first!!! Set up is 502 ci big block, iron heads, small roller 685/692, victor intake with 950 proform carb. 9 3/4 compression. Exhaust is spintech xl sportsmans 3 1/2 inch with dr. gas x-pipe and turn downs at the axle.

http://s62.photobucket.com/albums/h85/f ... ndclip.flv

Scott

Here is a short vid of mine. I have cheapo, unknown brand headers, 3 inch JEGS universal X-pipe into 3 inch Flowmaster Super 40 mufflers and 3 inch turn downs in front of the rear axle. It is loud and deep at idle, not as bad from 3000 to 3500 rpm on the highway. Motor combo is in sig.

http://s270.photobucket.com/albums/jj87 ... 0_0699.flv

Here was my old setup. 2.5" pipes, flowmaster mufflers, no X, or H pipe, full exhaust dumping behind the rear quarter panels GN style. Engine was a 408 with 10:5.1 compression.

http://www.youtube.com/watch?v=sqGNMm7SJ4s

Fix your link!

Here's one I did in January just before I pulled the motor out.
9:1 350, Vortecs, Comp XE268H cam, Hooker Comp. headers, 2¼" exhaust with Flo Pro mufflers & turndowns.
http://www.youtube.com/watch?v=GWMDs9issUc

I'll replace this one with one I get later, after the motor's finished being rebuilt.

Well my car is nothing impressive compared to a few of these others but i have a video just at idle though, crate 350, full headers, 2.25" pipe to flowmaster 40's no x or h

Link fixed!!!!

http://www.youtube.com/watch?v=y0wYGWnlLtE

mine is Hooker supercomp headers to 2.5" straight pipe-Dynomax ultraflos with dumps before rear axle

Dynomax Bullets, 3.5 inch, http://store.summitracing.com/partdetail.asp?autofilter=1&part=WLK%2D24216&N=700+115&autoview=sku

BBC 468, Flat Tappet Solid Lifter Cam, Production Iron Heads

single 4" dynomax round race mufflers on 406.

verry old video

http://videos.streetfire.net/video/turb ... h_9289.htm

406 with 1 3/4 Schoenfeld's, 3inch system and x-pipe. Flowmaster 40's with turn downs.

http://s268.photobucket.com/albums/jj29 ... levid1.flv

Big block 402, 11.5:1 compression, 0.550 lift comp cams magnum cam, hooker headers, custom 2.5 inch mandrel bent exhaust, straight back into 2 flowmaster 40's, 'Megs' exhaust tips.

First link is better sound, second is better visual.
http://www.youtube.com/watch?v=5hrbi3nU62E
http://www.youtube.com/watch?v=DBCq8k1ehbE

Here is the same engine, with two different exhaust systems.

The first two vids, in my car, 3" Dr Gas X-pipe, Flowmaster Delta Force 2 chamber mufflers then turndowns behind my 355" SBO

http://videos.streetfire.net/video/Some ... d_6751.htm
Man this is an ooooooold video!

http://videos.streetfire.net/video/My-1 ... a_6474.htm
Same setup, from the stands

The third video, 3" Flowtech X-pipe, Magnaflow mufflers, turndowns also behind my 355" SBO in another car:

http://videos.streetfire.net/video/SMuc ... 140463.htm

i used to have a video with my 87 malibu with 4" borlas............let me see if i can find it

Please do. I haven't heard a decent quality sound clip yet of the Borla's.

Anyone running UltraFlo's with an X-pipe?

Floorboard, did you lose any hp going to the Spintech's? Are they better than the Flowmaster, comparable to a straight through? They sound (in that vid) alot like my Flowmaster Super 40's.